Skip to Content

Wall drain · patented

Wall-In Nomina. Your tile, right up to the wall.

The cover takes your own tile or comes in four brushed finishes. Made to length between 30 and 160 cm.

your tileThe cover takes the floor tile, or four brushed finishes
30 – 160 cmmade to length, wall-to-wall
48 l/minBuild height 60–125 mm, suitable for renovation too

Build-up

Finely adjusted, quickly installed.

The patented adjustable eccentric flange allows fine levelling, and the drain body adapts to the tile thickness. Installation stays simple and fast.

Channel body and cover can be cut to any size from 30 cm.

Four finishes, or your own tile.

The same drain body. The cover decides how the wall edge reads.

Anthracite PVD
Anthracite PVD
Gold PVD
Gold PVD
Bronze PVD
Bronze PVD
Tileable cover
Tileable — your own tile

Build-up

Every part of the set.

Scroll: cover, tile carrier, flush-mounted box, drain body with the textile flange, the levelling parts and the siphon come apart.

The waterproofing membrane is fitted in the factory and connects to the bonded waterproofing. The eccentric flange levels the body to the tile thickness, and the siphon stays accessible from the front.

The tiles shown as transparent outlines are by others and not part of the delivery.

Scroll: the Wall-In Nomina set comes apart.

Technical data.

MaterialStainless steel 1.4301 / V2A (AISI 304)
LengthsMade to length, 30–160 cm
Build height60–125 mm
Installation stepspatented eccentric flange for fine levelling, drain body adapts to the tile thickness
DrainDN 50 outlet, trap
WaterproofingWaterproofing membrane, abP; connects to the bonded waterproofing
TestingabP, EN 1253

Ordering information.

Five covers, made to length.

Item numberSizeSurface
LW9 · Nomina — tileable or stainless coverMade to length between 30 and 160 cm.
LW9-H24L120E1120 cmBrushed stainless steel
LW9-H24L120E4120 cmBrushed gold (PVD)
LW9-H24L120E7120 cmBrushed bronze (PVD)
LW9-H24L120E9120 cmBrushed anthracite
—120 cmTileable cover — for your own tile
Made for your project — special lengthsAny length between 30 and 160 cm; lead time on request.

Identical for every variant: Material Stainless steel 1.4301 / V2A (AISI 304) · Outlet DN 50

Special lengths on request. Every channel can be cut to size on site.

Installation in five steps.

The order follows the site: shell first, tile last.

Stud wallPosition the drain body in the stud wall installation and connect it to the drainage.
ScreedLay the screed with a fall towards the wall.
WaterproofingBond the factory-fitted waterproofing membrane into the adjoining bonded waterproofing system, then seal wall and floor.
Tiling workTile the floor up to the underside of the trim, then the wall above it.
TrimAdjust the eccentric flange, fit the trim and peel off the protective film.

Installation

Installation step by step.

Nineteen steps from the wall opening to the finished joint. Click a step or let it run.

Prepare the wall opening
1Prepare the wall openingCreate the recess in the wall: at least 70 mm deep and 300 mm wide.
Set the height
2Set the heightMeasure the installation height and align the drain with the waste pipe.
Remove the transport bracket
3Remove the transport bracketTake off the transport bracket and dispose of it.
Mark the fixing points
4Mark the fixing pointsMark the fixing points on the wall and set the mounting feet.
Set the body in place
5Set the body in placePress the drain body onto the feet and align it in the opening.
Connect the waste pipe
6Connect the waste pipePush the spigot into the waste pipe.
Check for leaks
7Check for leaksPour in water and check the connection for tightness before building it in.
Fix the body
8Fix the bodyScrew the body tight and check that it is level.
Lay the screed
9Lay the screedBring the screed up to the drain with a fall of 1-2 % towards it.
Close the wall
10Close the wallBuild the wall up around the box and comb tile adhesive onto the surface.
Fold out the membrane
11Fold out the membraneFold the factory-fitted waterproofing membrane outwards onto the floor and wall.
Bed in the membrane
12Bed in the membraneBed the membrane into the adhesive and press it out flat.
Apply the bonded waterproofing
13Apply the bonded waterproofingRoll the waterproofing onto the floor first, then up the wall.
Cut the tile carrier to length
14Cut the tile carrier to lengthShorten the tileable cover profile with an INOX disc and deburr the edge.
Fit the end pieces
15Fit the end piecesSlide the end cap onto the profile and push the clip into place.
Insert the profile and level it
16Insert the profile and level itSet the tile carrier into the channel and check it with a spirit level.
Comb on the tile adhesive
17Comb on the tile adhesiveApply tile adhesive to the wall around the channel with a notched trowel.
Bond the cover tile
18Bond the cover tileButter the tile strip and slide it into the groove of the tile carrier.
Close the channel
19Close the channelPush the tiled cover home; the channel closes flush with the tiled wall.

Frequently asked questions.

What makes Wall-In different from a floor channel?

Wall-In sits in the wall and runs from wall to wall, so the floor surface stays uninterrupted and no channel is visible in the tiled floor. The design is patented.

Which lengths is Wall-In available in?

80, 100 and 120 cm. It can be cut on site down to 30 cm.

Which build height does Wall-In need?

From 60 mm, measured from the top of the raw floor.

How is Wall-In levelled?

With a patented eccentric flange for fine levelling. The drain body adapts to the tile thickness.

Is Wall-In suitable for bonded waterproofing?

Yes. The waterproofing membrane is fitted at the factory. Wall-In is tested to EN 1253 and holds a German abP.

Which outlet does Wall-In have?

A DN 50 outlet with a trap.

Specification text for tenders.

Ready to paste into your bill of quantities (German, as used in German tenders).

Wandablauf Fabrikat Gruen, Typ Wall-In Nomina, oder gleichwertig, Ablaufkörper für den Einbau in die Vorwand, Rinne aus Edelstahl 1.4301 (V2A), Abdeckung befliesbar oder in Edelstahl gebürstet (Edelstahl, Anthrazit, Bronze, Gold), auf Maß gefertigt zwischen 30 und 160 cm, mit patentiertem Exzenterflansch zur Feinjustierung, herausnehmbarem Haarsieb und Geruchsverschluss, Abgang DN 50, Aufbauhöhe 60–125 mm. Dichtmanschette werkseitig angebracht, für Verbundabdichtung geeignet. Ablaufleistung 0,80 l/s nach EN 1253, abP-geprüft. Länge ____ cm. Art.-Nr. LW9-H24L___E_.

Copy text